MX50_ARM2 U-Boot > mmc read 0 ${loadaddr} 0x800 0x1400;mmc read 0 ${loadaddr_ramdisk} 0x2800 0x258;bootm ${loadaddr} ${loadaddr_ramdisk} bootdev=0 MMC read: dev # 0, block # 2048, count 5120 partition # 0 ... imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x4 imx_esdhc.c bus_width 0x4 SD set clock 50MHz 5120 blocks read: OK MMC read: dev # 0, block # 10240, count 600 partition # 0 ... imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x4 imx_esdhc.c bus_width 0x4 SD set clock 50MHz 600 blocks read: OK ## Booting kernel from Legacy Image at 70800000 ... Image Name: Normal Kernel Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2288064 Bytes = 2.2 MB Load Address: 70008000 Entry Point: 70008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 70c00000 ... Image Name: Normal Rootfs Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 286848 Bytes = 280.1 kB Load Address: 70308000 Entry Point: 70308000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Linux version 2.6.35.3 (hudson@devuntu5) (gcc version 4.4.0 (GCC) ) #1 PREEMPT Wed May 7 15:03:54 JST 2014 CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Freescale MX50 ARM2 Board Ignoring unrecognised tag 0x54410008 Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 63754 Kernel command line: root=/dev/mmcblk0p1 rootfstype=ext4 rw rootwait init=/linuxrc console=ttymxc4,115200 bootdev=0 rawtable=0xF40000 PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 251MB = 251MB total Memory: 249148k/249148k available, 7876k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xf9e00000 - 0xffe00000 ( 96 MB) vmalloc : 0x90000000 - 0xf4000000 (1600 MB) lowmem : 0x80000000 - 0x8fb00000 ( 251 MB) pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) modules : 0x7f000000 - 0x7fe00000 ( 14 MB) .init : 0x80008000 - 0x80025000 ( 116 kB) .text : 0x80025000 - 0x80424000 (4092 kB) .data : 0x80444000 - 0x804be700 ( 490 kB) SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled. NR_IRQS:396 MXC GPIO hardware MXC IRQ initialized You should not call the gpmi_set_parent MXC_Early serial console at MMIO 0x63f90000 (options '115200') bootconsole [ttymxc4] enabled Console: colour dummy device 80x30 Mix log static memory : 7fe00000 - 7fffffff address : 90400000 There is not the last log. Initialize a static memory for mix_logger. ##### LOG START ##### Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok regulator: core version 0.5 NET: Registered protocol family 16 i.MX IRAM pool: 128 KB@0x90040000 CPU is i.MX50 Revision 1.1 IR Power is LDO4 This is TPS65181. PWR3DET:power 3 detect FEC disable Using SDMA I.API MXC DMA API initialized IMX usb wakeup probe IMX usb wakeup probe bio: create slab at 0 CSPI: mxc_spi-0 probed CSPI: mxc_spi-2 probed usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb wm831x 0-0034: WM8321 revision C regulator: VCORE: 850 <--> 1100 mV at 1000 mV at 0 uA regulator: VPERI: 950 <--> 1250 mV at 1250 mV at 0 uA regulator: DCDC3: at 1800 mV regulator: DCDC4: at 2900 mV regulator: LDO1: 900 <--> 3300 mV at 1200 mV regulator: LDO2: 900 <--> 3300 mV at 1200 mV regulator: LDO3: 900 <--> 3300 mV at 2500 mV regulator: LDO4: 900 <--> 3300 mV at 3200 mV regulator: LDO5: 900 <--> 3300 mV at 2900 mV regulator: LDO6: 900 <--> 3300 mV at 2500 mV regulator: LDO7: 1000 <--> 3500 mV at 1800 mV regulator: LDO8: 1000 <--> 3500 mV at 2500 mV regulator: LDO9: 1000 <--> 3500 mV at 3100 mV regulator: LDO10: 1000 <--> 3500 mV at 3200 mV regulator: LDO11: 800 <--> 1550 mV at 1200 mV Advanced Linux Sound Architecture Driver Version 1.0.23. Switching to clocksource mxc_timer1 mxsdhci: MXC Secure Digital Host Controller Interface driver mxsdhci: MXC SDHCI Controller Driver. SDHC:sdhci_set_power:slot pwr off mmc_detect_change: id=0 mmc0: SDHCI detect irq 179 irq 1 INTERNAL DMA mxsdhci: MXC SDHCI Controller Driver. SDHC:sdhci_set_power:slot pwr on mmc_detect_change: id=1 mmc1: SDHCI detect irq 0 irq 2 INTERNAL DMA mxsdhci: MXC SDHCI Controller Driver. mmc_detect_change: id=2 mmc2: SDHCI detect irq 228 irq 3 INTERNAL DMA mxsdhci: MXC SDHCI Controller Driver. mmc_detect_change: id=3 mmc3: SDHCI detect irq 0 irq 4 INTERNAL DMA NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Unpacking initramfs... Freeing initrd memory: 280K LPMode driver module loaded Static Power Management for Freescale i.MX5 PM driver module loaded sdram autogating driver module loaded Bus freq driver module loaded mxc_dvfs_core_probe DVFS driver module loaded i.MXC CPU frequency driver DVFS PER driver module loaded ashmem: initialized msgmni has been set to 487 alg: No test for stdrng (krng) cryptodev: driver loaded. io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) regulator: DISPLAY: regulator: VCOM: at 1250 mV regulator: V3P3_CTRL: regulator: PMIC_TEMP: regulator: PWR0_CTRL: regulator: PWR2_CTRL: SDHC:sdhci_set_power:slot pwr on regulator: VSYS_EPD: tps65180 1-0048: PMIC TPS6518x for eInk display mmc0: new high speed SDHC card at address 0007 mmc_rescan:wake_lock_timeout (0) mmc_rescan:detect done(id=0) mmc2: new high speed MMC card at address 0001 mmc_rescan:wake_lock_timeout (2) mmc_rescan:wifi:wake unlock (3) Serial: MXC Internal UART driver mxcuart register mxcintuart.2: ttymxc2 at MMIO 0x5000c000 (irq = 33) is a Freescale i.MX mxcintuart.3: ttymxc3 at MMIO 0x53ff0000 (irq = 13) is a Freescale i.MX mxcintuart.4: ttymxc4 at MMIO 0x63f90000 (irq = 86) is a Freescale i.MX console [ttymxc4] enabled, bootconsole disabled console [ttymxc4] enabled, bootconsole disabled mxcswuart register mxcintswuart.0: ttymxc0 at MMIO 0x53fbc000 (irq = 31) is a Freescale i.MX SSW:ssw port register 0 mxcintswuart.1: ttymxc1 at MMIO 0x53fc0000 (irq = 32) is a Freescale i.MX SSW:ssw port register 1 loop: module loaded FEC Ethernet Driver PPP generic driver version 2.4.2 usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver net1080 usbcore: registered new interface driver cdc_subset input: gpio-keys as /devices/platform/gpio-keys/input/input0 irtp_init irtp_connect input: SONY IR Touchpanel as /devices/virtual/input/input1 IRTP: register early_suspend input: wm831x_on as /devices/platform/imx-i2c.0/i2c-0/0-0034/wm831x-on/input/input2 input: phxlit_vbus as /devices/platform/phxlit_vbus.0/input/input3 phxlit_vbus phxlit_vbus.0: event(type 5 code 12) wm831x-rtc wm831x-rtc: rtc core: registered wm831x as rtc0 mxc_rtc mxc_rtc.0: rtc core: registered mxc_rtc as rtc1 using rtc device, wm831x, for alarms i2c /dev entries driver APM Battery Driver MXC WatchDog Driver 2.0 MXC Watchdog # 0 Timer: initial timeout 60 sec mmcblk0: mmc0:0007 SD16G 14.4 GiB mmcblk0: p1 p2 p3 < p5 p6 p7 p8 p9 p10 > p4 Raw data table load mmcblk2: mmc2:0001 SEM02G 1.82 GiB BUG: recent printk recursion! <6> mmcblk2: logger: created 64K log 'log_main' logger: created 64K log 'log_events' logger: created 64K log 'log_radio' logger: created 64K log 'log_system' logger: created 2047K log 'log_mix' logger: created 64K log 'log_kernel' Past log manager. CS42L52: CODEC revision C1 DMA Sound Buffers Allocated:UseIram=1 buf->addr=f8006000 buf->area=90046000 size=24576 DMA Sound Buffers Allocated:UseIram=1 buf->addr=7e328000 buf->area=f9e01000 size=24576 asoc: CS42L52 dai <-> imx-ssi-2-0 mapping ok ALSA device list: #0: imx-3stack (CS42L52 codec) nf_conntrack version 0.5.0 (3897 buckets, 15588 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 17 VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2 tps65180_vsys_enable : wait VSYS_EPD. regulator_init_complete: incomplete constraints, leaving PWR2_CTRL on regulator_init_complete: incomplete constraints, leaving PMIC_TEMP on epdc_progress_work_func start progress. regulator_init_complete: incomplete constraints, leaving LDO11 on regulator_init_complete: incomplete constraints, leaving LDO7 on regulator_init_complete: incomplete constraints, leaving LDO6 on regulator_init_complete: incomplete constraints, leaving LDO5 on regulator_init_complete: incomplete constraints, leaving LDO3 on regulator_init_complete: incomplete constraints, leaving LDO2 on regulator_init_complete: incomplete constraints, leaving LDO1 on input: sub_cpu_pwrbutton as /devices/platform/mxc_spi.2/spi3.2/sub_cpu_pwrbutton/input/input4 wm831x-rtc wm831x-rtc: hctosys: unable to read the hardware clock wm831x-rtc wm831x-rtc: setting system clock to 2010-01-01 00:00:00 UTC (1262304000) Freeing init memory: 116K init: cannot open '/initlogo.rle' EXT4-fs (mmcblk0p6): mounted filesystem without journal. Opts: (null) EXT4-fs (mmcblk0p8): mounted filesystem without journal. Opts: (null) EXT4-fs (mmcblk0p10): mounted filesystem without journal. Opts: (null) EXT4-fs (mmcblk0p10): re-mounted. Opts: (null) EXT4-fs (mmcblk0p9): warning: maximal mount count reached, running e2fsck is recommended EXT4-fs (mmcblk0p9): recovery complete EXT4-fs (mmcblk0p9): mounted filesystem with ordered data mode. Opts: (null) init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' warning: `wpa_supplicant' uses 32-bit capabilities (legacy support in use) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.1: irq 14, io base 0x53f80200 fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ARC USBOTG Device Controller driver (1 August 2005) Android usb driver initialize android_usb gadget: android_usb ready fsl-usb2-udc: bind to driver android_usb android gadget: register function adb android gadget: register function usb_mass_storage android_usb gadget: usb_mass_storage, version: 2009/09/11 android_usb gadget: Number of LUNs=3 lun0: [Sony PRS-T1 2001 ] lun1: [Sony PRS-T1 SD 2001 ] lun2: [Sony PRS-T1 Setting 2001 ] enabling adb enable function for:adb, id:1474 it is ACTIVE host android_usb gadget: high speed config #1: android epdc_progress_work_func end progress. request_suspend_state: on (3->0) at 18323830126 (2010-01-01 00:00:16.802811750 UTC) power key is enabled request_suspend_state: standby (0->1) at 42513546393 (2010-01-01 00:00:40.992518392 UTC) mxc_rtc alarms after 180 sec