U-Boot 2009.08 (Sep 01 2011 - 21:01:15) CPU: Freescale i.MX50 family 1.1V at 800 MHz mx50 pll1: 800MHz mx50 pll2: 400MHz mx50 pll3: 216MHz ipg clock : 66666666Hz ipg per clock : 66666666Hz uart clock : 24000000Hz ahb clock : 133333333Hz axi_a clock : 400000000Hz axi_b clock : 200000000Hz weim_clock : 100000000Hz ddr clock : 160000000Hz esdhc1 clock : 80000000Hz esdhc2 clock : 80000000Hz esdhc3 clock : 80000000Hz esdhc4 clock : 80000000Hz Board: MX50 ARM2 board Boot Reason: [POR] Boot Device: MMC I2C: ready DRAM: 256 MB MMC: FSL_ESDHC: 0, FSL_ESDHC: 1, FSL_ESDHC: 2 imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x4 imx_esdhc.c bus_width 0x4 MMC set clock 50MHz imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x4 imx_esdhc.c bus_width 0x4 MMC set clock 50MHz imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x4 imx_esdhc.c bus_width 0x4 MMC set clock 50MHz imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x4 imx_esdhc.c bus_width 0x4 MMC set clock 50MHz temperature -10 imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x4 imx_esdhc.c bus_width 0x4 MMC set clock 50MHz In: serial Out: serial Err: serial Net: got MAC address from IIM: 00:00:00:00:00:00 FEC0 Hit any key to stop autoboot: 0 MMC read: dev # 0, block # 2048, count 5120 partition # 0 ... imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x4 imx_esdhc.c bus_width 0x4 SD set clock 50MHz 5120 blocks read: OK MMC read: dev # 0, block # 10240, count 600 partition # 0 ... imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x1 imx_esdhc.c bus_width 0x4 imx_esdhc.c bus_width 0x4 SD set clock 50MHz 600 blocks read: OK ## Booting kernel from Legacy Image at 70800000 ... Image Name: Linux-2.6.35.3 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1934624 Bytes = 1.8 MB Load Address: 70008000 Entry Point: 70008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 70c00000 ... Image Name: Normal Rootfs Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 286848 Bytes = 280.1 kB Load Address: 70308000 Entry Point: 70308000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Linux version 2.6.35.3 (build@inkbox) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #8 PREEMPT Thu Jun 2 17:57:52 EDT 2022 CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Freescale MX50 ARM2 Board Ignoring unrecognised tag 0x54410009 Ignoring unrecognised tag 0x54410008 Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 63754 Kernel command line: console=ttymxc4,115200 rawtable=0xF40000 root=/dev/ram0 rdinit=/sbin/init rootfstype=ramfs PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 251MB = 251MB total Memory: 248944k/248944k available, 8080k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xf9e00000 - 0xffe00000 ( 96 MB) vmalloc : 0x90000000 - 0xf4000000 (1600 MB) lowmem : 0x80000000 - 0x8fb00000 ( 251 MB) pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) modules : 0x7f000000 - 0x7fe00000 ( 14 MB) .init : 0x80008000 - 0x80065000 ( 372 kB) .text : 0x80065000 - 0x80456000 (4036 kB) .data : 0x80474000 - 0x804ee7e0 ( 490 kB) SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled. NR_IRQS:396 MXC GPIO hardware MXC IRQ initialized You should not call the gpmi_set_parent MXC_Early serial console at MMIO 0x63f90000 (options '115200') bootconsole [ttymxc4] enabled Console: colour dummy device 80x30 Mix log static memory : 7fe00000 - 7fffffff address : 90400000 There is not the last log. Initialize a static memory for mix_logger. ##### LOG START ##### Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok devtmpfs: initialized regulator: core version 0.5 NET: Registered protocol family 16 i.MX IRAM pool: 128 KB@0x90040000 CPU is i.MX50 Revision 1.1 IR Power is LDO4 This is TPS65181. PWR3DET:power 3 detect FEC disable Using SDMA I.API MXC DMA API initialized IMX usb wakeup probe IMX usb wakeup probe bio: create slab at 0 CSPI: mxc_spi-0 probed CSPI: mxc_spi-2 probed usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb wm831x 0-0034: WM8321 revision C wm831x 0-0034: Security key had non-zero value 1 regulator: VCORE: 850 <--> 1100 mV at 1000 mV at 0 uA regulator: VPERI: 950 <--> 1250 mV at 1250 mV at 0 uA regulator: DCDC3: at 1800 mV regulator: DCDC4: at 2900 mV regulator: LDO1: 900 <--> 3300 mV at 1200 mV regulator: LDO2: 900 <--> 3300 mV at 1200 mV regulator: LDO3: 900 <--> 3300 mV at 2500 mV regulator: LDO4: 900 <--> 3300 mV at 3200 mV regulator: LDO5: 900 <--> 3300 mV at 2900 mV regulator: LDO6: 900 <--> 3300 mV at 2500 mV regulator: LDO7: 1000 <--> 3500 mV at 1800 mV regulator: LDO8: 1000 <--> 3500 mV at 2500 mV regulator: LDO9: 1000 <--> 3500 mV at 3100 mV regulator: LDO10: 1000 <--> 3500 mV at 3200 mV regulator: LDO11: 800 <--> 1550 mV at 1200 mV Advanced Linux Sound Architecture Driver Version 1.0.23. Switching to clocksource mxc_timer1 mxsdhci: MXC Secure Digital Host Controller Interface driver(all reset on error version) mxsdhci: MXC SDHCI Controller Driver. mmc0: SDHCI detect irq 179 irq 1 INTERNAL DMA mxsdhci: MXC SDHCI Controller Driver. mmc1: SDHCI detect irq 0 irq 2 INTERNAL DMA mxsdhci: MXC SDHCI Controller Driver. mmc2: SDHCI detect irq 228 irq 3 INTERNAL DMA mxsdhci: MXC SDHCI Controller Driver. mmc3: SDHCI detect irq 0 irq 4 INTERNAL DMA NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... Freeing initrd memory: 280K LPMode driver module loaded Static Power Management for Freescale i.MX5 PM driver module loaded sdram autogating driver module loaded Bus freq driver module loaded mxc_dvfs_core_probe DVFS driver module loaded i.MXC CPU frequency driver DVFS PER driver module loaded ashmem: initialized msgmni has been set to 486 alg: No test for stdrng (krng) cryptodev: driver loaded. io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) regulator: DISPLAY: regulator: VCOM: at 1250 mV regulator: V3P3_CTRL: regulator: PMIC_TEMP: regulator: PWR0_CTRL: regulator: PWR2_CTRL: regulator: VSYS_EPD: tps65180 1-0048: PMIC TPS6518x for eInk display mmc0: new high speed SDHC card at address 1234 mmc2: new high speed MMC card at address 0001 Serial: MXC Internal UART driver mxcuart register mxcintuart.2: ttymxc2 at MMIO 0x5000c000 (irq = 33) is a Freescale i.MX mxcintuart.3: ttymxc3 at MMIO 0x53ff0000 (irq = 13) is a Freescale i.MX mxcintuart.4: ttymxc4 at MMIO 0x63f90000 (irq = 86) is a Freescale i.MX console [ttymxc4] enabled, bootconsole disabled console [ttymxc4] enabled, bootconsole disabled mxcswuart register mxcintswuart.0: ttymxc0 at MMIO 0x53fbc000 (irq = 31) is a Freescale i.MX SSW:ssw port register 0 mxcintswuart.1: ttymxc1 at MMIO 0x53fc0000 (irq = 32) is a Freescale i.MX SSW:ssw port register 1 brd: module loaded loop: module loaded FEC Ethernet Driver PPP generic driver version 2.4.2 usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver net1080 usbcore: registered new interface driver cdc_subset input: gpio-keys as /devices/platform/gpio-keys/input/input0 irtp_init irtp_connect input: SONY IR Touchpanel as /devices/virtual/input/input1 IRTP: register early_suspend input: wm831x_on as /devices/platform/imx-i2c.0/i2c-0/0-0034/wm831x-on/input/input2 input: phxlit_vbus as /devices/platform/phxlit_vbus.0/input/input3 phxlit_vbus phxlit_vbus.0: event(type 5 code 12) wm831x-rtc wm831x-rtc: rtc core: registered wm831x as rtc0 mxc_rtc mxc_rtc.0: rtc core: registered mxc_rtc as rtc1 using rtc device, wm831x, for alarms i2c /dev entries driver APM Battery Driver MXC WatchDog Driver 2.0 MXC Watchdog # 0 Timer: initial timeout 60 sec mmcblk0: mmc0:1234 SA04G 3.67 GiB mmcblk0: p1 p2 p3 < p5 p6 p7 p8 p9 p10 > p4 mmcblk2: mmc2:0001 SEM02G 1.82 GiB mmcblk2: p1 p2 p3 < p5 p6 p7 p8 p9 p10 > p4 logger: created 64K log 'log_main' logger: created 64K log 'log_events' logger: created 64K log 'log_radio' logger: created 64K log 'log_system' logger: created 2047K log 'log_mix' logger: created 64K log 'log_kernel' Past log manager. [PASTLOG Err:past_mmc_initialize(502)]Open error CS42L52: CODEC revision C1 DMA Sound Buffers Allocated:UseIram=1 buf->addr=f8006000 buf->area=90046000 size=24576 DMA Sound Buffers Allocated:UseIram=1 buf->addr=79028000 buf->area=f9e01000 size=24576 asoc: CS42L52 dai <-> imx-ssi-2-0 mapping ok ALSA device list: #0: imx-3stack (CS42L52 codec) nf_conntrack version 0.5.0 (3894 buckets, 15576 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 17 VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2 tps65180_vsys_enable : wait VSYS_EPD. regulator_init_complete: incomplete constraints, leaving PWR2_CTRL on regulator_init_complete: incomplete constraints, leaving PMIC_TEMP on epdc_progress_work_func start progress. tps65180_display_enable fail to read vcom from eMMC. -1 mxc_epdc_fb mxc_epdc_fb: Unable to enable DISPLAY regulator.err = 0xffffffff ------------[ cut here ]------------ WARNING: at drivers/regulator/core.c:1423 _regulator_disable+0x30/0x118() unbalanced disables for DISPLAY Modules linked in: [<8006a66c>] (unwind_backtrace+0x0/0xec) from [<8008aca8>] (warn_slowpath_common+0x4c/0x64) [<8008aca8>] (warn_slowpath_common+0x4c/0x64) from [<8008ad40>] (warn_slowpath_fmt+0x2c/0x3c) [<8008ad40>] (warn_slowpath_fmt+0x2c/0x3c) from [<801fa178>] (_regulator_disable+0x30/0x118) [<801fa178>] (_regulator_disable+0x30/0x118) from [<801fa338>] (regulator_disable+0x1c/0x30) regulator_init_complete: incomplete constraints, leaving LDO11 on [<801fa338>] (regulator_disable+0x1c/0x30) from [<801f44bc>] (epdc_powerup+0x2ac/0x32c) [<801f44bc>] (epdc_powerup+0x2ac/0x32c) from [<801f5a28>] (epdc_progress_work_func+0x58/0x13c) [<801f5a28>] (epdc_progress_work_func+0x58/0x13c) from [<8009d58c>] (worker_thread+0x178/0x228) [<8009d58c>] (worker_thread+0x178/0x228) from [<800a08c8>] (kthread+0x78/0x80) [<800a08c8>] (kthread+0x78/0x80) from [<800669c0>] (kernel_thread_exit+0x0/0x8) ---[ end trace 57e1e4ef223bfc3b ]--- regulator_init_complete: incomplete constraints, leaving LDO7 on regulator_init_complete: incomplete constraints, leaving LDO6 on regulator_init_complete: incomplete constraints, leaving LDO5 on powerup retry. tps65180_display_enable fail to read vcom from eMMC. -1 mxc_epdc_fb mxc_epdc_fb: Unable to enable DISPLAY regulator.err = 0xffffffff ------------[ cut here ]------------ WARNING: at drivers/regulator/core.c:1423 _regulator_disable+0x30/0x118() unbalanced disables for DISPLAY Modules linked in: regulator_init_complete: incomplete constraints, leaving LDO3 on [<8006a66c>] (unwind_backtrace+0x0/0xec) from [<8008aca8>] (warn_slowpath_common+0x4c/0x64) [<8008aca8>] (warn_slowpath_common+0x4c/0x64) from [<8008ad40>] (warn_slowpath_fmt+0x2c/0x3c) [<8008ad40>] (warn_slowpath_fmt+0x2c/0x3c) from [<801fa178>] (_regulator_disable+0x30/0x118) [<801fa178>] (_regulator_disable+0x30/0x118) from [<801fa338>] (regulator_disable+0x1c/0x30) [<801fa338>] (regulator_disable+0x1c/0x30) from [<801f44bc>] (epdc_powerup+0x2ac/0x32c) [<801f44bc>] (epdc_powerup+0x2ac/0x32c) from [<801f5a28>] (epdc_progress_work_func+0x58/0x13c) [<801f5a28>] (epdc_progress_work_func+0x58/0x13c) from [<8009d58c>] (worker_thread+0x178/0x228) [<8009d58c>] (worker_thread+0x178/0x228) from [<800a08c8>] (kthread+0x78/0x80) regulator_init_complete: incomplete constraints, leaving LDO2 on [<800a08c8>] (kthread+0x78/0x80) from [<800669c0>] (kernel_thread_exit+0x0/0x8) ---[ end trace 57e1e4ef223bfc3c ]--- powerup retry out. (powerup error count: 1 epdc_progress_work_func Fails to powerup.-1 epdc_progress_work_func end progress. regulator_init_complete: incomplete constraints, leaving LDO1 on input: sub_cpu_pwrbutton as /devices/platform/mxc_spi.2/spi3.2/sub_cpu_pwrbutton/input/input4 wm831x-rtc wm831x-rtc: setting system clock to 2011-01-01 09:17:22 UTC (1293873442) tps65180_display_enable fail to read vcom from eMMC. -1 ------------[ cut here ]------------ WARNING: at drivers/regulator/core.c:1423 _regulator_disable+0x30/0x118() unbalanced disables for DISPLAY Modules linked in: [<8006a66c>] (unwind_backtrace+0x0/0xec) from [<8008aca8>] (warn_slowpath_common+0x4c/0x64) [<8008aca8>] (warn_slowpath_common+0x4c/0x64) from [<8008ad40>] (warn_slowpath_fmt+0x2c/0x3c) [<8008ad40>] (warn_slowpath_fmt+0x2c/0x3c) from [<801fa178>] (_regulator_disable+0x30/0x118) [<801fa178>] (_regulator_disable+0x30/0x118) from [<801fa338>] (regulator_disable+0x1c/0x30) [<801fa338>] (regulator_disable+0x1c/0x30) from [<8026a410>] (get_temperature+0x40/0x50) [<8026a410>] (get_temperature+0x40/0x50) from [<8026a42c>] (calculate_battery_capacity+0xc/0x8c) [<8026a42c>] (calculate_battery_capacity+0xc/0x8c) from [<80354958>] (sub_cpu_bci_probe+0x2b4/0x36c) [<80354958>] (sub_cpu_bci_probe+0x2b4/0x36c) from [<80223930>] (platform_drv_probe+0x18/0x1c) [<80223930>] (platform_drv_probe+0x18/0x1c) from [<80222ad0>] (driver_probe_device+0xc8/0x184) [<80222ad0>] (driver_probe_device+0xc8/0x184) from [<80222bec>] (__driver_attach+0x60/0x84) [<80222bec>] (__driver_attach+0x60/0x84) from [<802222ec>] (bus_for_each_dev+0x44/0x74) [<802222ec>] (bus_for_each_dev+0x44/0x74) from [<80221c40>] (bus_add_driver+0x98/0x214) [<80221c40>] (bus_add_driver+0x98/0x214) from [<80222ed8>] (driver_register+0xa8/0x138) [<80222ed8>] (driver_register+0xa8/0x138) from [<80065370>] (do_one_initcall+0x58/0x1a8) [<80065370>] (do_one_initcall+0x58/0x1a8) from [<80008408>] (kernel_init+0xa8/0x168) [<80008408>] (kernel_init+0xa8/0x168) from [<800669c0>] (kernel_thread_exit+0x0/0x8) ---[ end trace 57e1e4ef223bfc3d ]--- Freeing init memory: 372K /proc/self/exeKernel panic - not syncing: Attempted to kill init! [<8006a66c>] (unwind_backtrace+0x0/0xec) from [<80355678>] (panic+0x6c/0xf0) [<80355678>] (panic+0x6c/0xf0) from [<8008e410>] (do_exit+0x68/0x67c) [<8008e410>] (do_exit+0x68/0x67c) from [<8008eb2c>] (complete_and_exit+0x0/0x1c) [<8008eb2c>] (complete_and_exit+0x0/0x1c) from [<80065f80>] (ret_fast_syscall+0x0/0x30)